Home maintenance · Published 2026-11-15 · Updated 2026-11-15
How to bleed a radiator: steps, tools and what to check after
A radiator that is cold at the top and warm at the bottom is usually holding trapped air. Letting it out takes a few minutes and costs nothing. This guide covers the tools, the order to work in, the boiler pressure check people forget, and the signs that the problem is something else.
Quick answer. Turn the heating off and let the radiators cool. Put a cloth under the bleed valve, turn it slowly anticlockwise with a radiator key until the hissing stops and water appears, then close it. Afterwards check the boiler pressure is between 1 and 2 bar and top it up if it has dropped.
How do I know a radiator needs bleeding?
Air is lighter than water, so it collects at the top of the radiator and stops hot water filling the panel. The classic sign is a radiator that is cool near the top and warm lower down. Other clues are gurgling noises, a radiator that takes a long time to warm up and rooms that never feel as warm as the rest of the house.
Switch the heating on and let it run for a while, then run a hand along the top of each radiator, taking care because they can be hot. A radiator that is hot all over does not need bleeding, so leave it alone.
What tools do I need?
If you have a combination boiler or sealed heating system, you will also need to know where the filling loop is. If you are not sure, our guide on what to check when your boiler stops working explains the pressure gauge in plain words.
- A radiator bleed key, which is cheap at any DIY shop. Many modern radiators take a flat head screwdriver instead.
- A cloth or small container to catch drips of dirty water.
- An old towel to protect the floor.
- Gloves, in case the water is hot.
- Your boiler manual, to find the filling loop if the pressure drops.
How do I bleed a radiator step by step?
Work in this order so you do not make a mess or waste time.
- Turn the central heating off and wait until the radiators are cool. Hot water and air can scald.
- If you have several radiators to do, start with the one on the ground floor furthest from the boiler and work towards it, then go upstairs.
- Hold the cloth under the bleed valve, which is usually at the top corner of the radiator on one side.
- Fit the key or screwdriver and turn it slowly anticlockwise, about a quarter turn. You should hear a hiss as the air escapes.
- When the hissing stops and a little water appears, close the valve straight away. Tighten it firmly, but do not force it.
- Wipe the valve and check there is no drip.
What must I check on the boiler afterwards?
Bleeding lets air out and a little water in, so the pressure in a sealed system often drops. Which? says to check the boiler pressure indicator, which should be between 1.0 and 2.0 bar, often shown in green. If it has fallen below 1 bar, top it up with the filling loop as your manual describes, then turn the heating back on.
Give the radiators time to heat and check that the cold area at the top has gone. If the boiler locks out after bleeding, it is usually the pressure, and you can read more in our boiler troubleshooting guide.
The radiator is still cold. What now?
If a radiator is cold at the bottom or the middle after bleeding, air is probably not the problem. Boiler maker Baxi says this can point to sludge or debris in the system, which a Gas Safe registered installer can flush out and treat with an inhibitor. A radiator that stays cold all over may have a stuck valve, a balancing problem or a circulation fault.
Bleeding radiators does not involve gas, but anything on the boiler itself does. Read our Gas Safe checklist before you let anyone open the boiler, and use the Coventry plumber directory for engineers who say they are registered. Always check the register yourself.
How often should I bleed my radiators?
Guides differ a little. Screwfix says at least once a year or whenever you notice cold spots, and Boxt says twice a year is plenty. Doing it before winter is a sensible habit. If you need to bleed the same radiator every few weeks, something else is wrong, and it is worth asking an engineer to look at the system.
Does bleeding really save money?
It helps the system work as it should, which avoids heating rooms that never warm up. We cannot give you a precise saving, because it depends on your home. The Energy Saving Trust figure quoted by Which? gives a sense of scale: turning the thermostat up by one degree costs about £75 a year. If cold spots make you turn it up, fixing them is worth a few minutes.
If you would rather not do it yourself, many handymen do small heating tasks, but check what they are insured and competent to do first. Our handyman or specialist guide shows where the line sits.
What about heated towel rails?
The same idea applies. Air collects at the top, and there is usually a bleed valve on one of the top corners. Use the same steps, then check the boiler pressure.
At a glance
| Step | What to do | Why |
|---|---|---|
| 1 | Heating off, radiators cool | Avoid scalds |
| 2 | Start with the radiator furthest from the boiler | Air moves along the pipes |
| 3 | Cloth under the valve | Catch dirty water |
| 4 | Quarter turn anticlockwise | Let air hiss out |
| 5 | Close when water appears | Keep the system sealed |
| 6 | Check pressure, 1 to 2 bar | Bleeding often lowers it |
Worked example: time for a typical house
| Item | Maths | Total |
|---|---|---|
| Time per radiator, up to 5 minutes (Radiator Hub) | 1 x 5 minutes | 5 minutes |
| Eight radiators | 8 x 5 minutes | 40 minutes |
| Extra for protecting floors and a pressure top up | Allow | 10 to 15 minutes |
| Twice a year, as Boxt suggests | 2 x 40 minutes | 80 minutes a year, before extras |
What a cold spot usually means
| Where it is cold | Likely cause | Action |
|---|---|---|
| Top of the radiator | Trapped air | Bleed it |
| Bottom or middle | Sludge or debris | Gas Safe installer, flush and inhibitor |
| Whole radiator | Closed or stuck valve, balancing or circulation | Check the valve, then an engineer |
| All radiators, pressure low | Low boiler pressure | Top up, check for leaks |
This is general guidance, not legal advice. Rules and prices change, so check the official sources listed below.
Questions
Which radiator should I bleed first?
Start with the ground floor radiator furthest from the boiler, then work towards it and go upstairs, as Which? Trusted Traders suggests.
Can I bleed a radiator with the heating on?
No. Turn it off and let the radiators cool first, as British Gas and Baxi both advise, because the water can be scalding.
How long does it take to bleed a radiator?
Up to about five minutes per radiator for most people. A whole house of eight radiators is around 40 minutes.
Why did my boiler pressure drop after bleeding?
Air has left the system. Top it up with the filling loop until it sits between 1 and 2 bar, as in your manual.
No air came out, only water. Is that normal?
It means there was no trapped air in that radiator. Close the valve and look for another cause if it is still cold.
What if I cannot find the bleed valve?
It is normally on a top corner. If you cannot find it, ask a plumber instead of forcing parts of the radiator.
Is bleeding a radiator gas work?
No, it is plumbing work on the radiator. Gas work on the boiler needs a Gas Safe registered engineer.
Why is my radiator cold at the bottom?
That is often sludge, not air. A Gas Safe installer can flush the system and add an inhibitor, according to Baxi.
Can a handyman do this for me?
Many can bleed radiators, though a handyman should not work on the boiler. For heating faults, a plumber is the safer choice.
How often should I do it?
Once or twice a year, and when you notice cold spots. If a radiator keeps needing it, ask for an engineer to check the system.
Sources
- Which?, how to bleed your radiators
- Which? Trusted Traders, how to balance and bleed your radiators
- Baxi, how to bleed a radiator
- British Gas, how to bleed a radiator
- Screwfix, bleeding a radiator guide
- Boxt, how to bleed a radiator
- Checkatrade, how to bleed a radiator
- The Radiator Hub, how to bleed a radiator
Keep reading
- Boiler not working? What to check
- How much does a boiler service cost?
- Find a plumber in Coventry
- Handymen in Earlsdon
- Why is my radiator cold at the bottom? Causes and fixes
- What does a plumber charge for a leaking tap in the UK?
- How to stop a dripping tap: washer, O-ring or cartridge
- Boiler pressure too low: what to do and how to top it up
- Find a handyman in Coventry
- How Coventry Home Fix works